Green Building Material Certificate



This epoxy resin is a thermosetting resin hardened by high-activity polyetheramine and Bisphenol-A epoxy resin. It has good fluidity, has an appropriate operating time, high mechanical properties, impact resistance, chemical resistance, and physical properties. It is widely used in construction and civil engineering resin mortar grouting, electronic parts filling and other purposes. This product is a healthy green building material.

Applications

  • Intermediate coating for filling and pouring.
  • Building civil engineering, mortar, grouting, wear-resistant floor materials.
  • Filling of electronic parts.

Features

  • Acid resistance.
  • Alkali resistance.
  • Impact resistance.
  • Pass the salt spray test.

Directions

  1. 1000g/m2 for one painting/coating.
  2. Mix agent A and agent B evenly according to the ratio and apply with trowel, roller brush or machine spray.
  3. Mix agent A and agent B evenly according to the ratio and apply with high-pressure pouring machine or a low-pressure injection barrel to repair cracks.

Notice

  1. The materials should be fully stirred according to the correct ratio, and no solvent or water should be added.
  2. The product should be stored in a cool, dry place and avoid direct sunlight.
  3. Avoid painting in rainy, humid climate or when the relative humidity of the weather is above 85 %.
  4. In case of accidental contact with eyes, skin, inhalation, or ingestion, please rinse with plenty of water and seek medical attention for emergency treatment immediately.


This epoxy resin topcoat is a thermosetting resin, and the hardened product has an excellent surface gloss. It is suitable for the coating of floor materials, surface gloss and decorations. This product is a healthy green building material.

Applications

  • Suitable for floor coatings and steel component coatings.
  • Wall coating.

Features

  • Acid resistance.
  • Alkali resistance.
  • Impact resistance.
  • Pass the salt spray test.

Directions

  1. 1000g/m2 for one painting/coating.
  2. Mix agent A and agent B evenly according to the ratio and apply with trowel, roller brush or machine spray.

Notice

  1. The materials should be fully stirred according to the correct ratio, and no solvent or water should be added.
  2. The product should be stored in a cool, dry place and avoid direct sunlight.
  3. Avoid painting in rainy, humid climate or when the relative humidity of the weather is above 85 %.
  4. In case of accidental contact with eyes, skin, inhalation, or ingestion, please rinse with plenty of water and seek medical attention for emergency treatment immediately.


It is an emulsified water-based epoxy resin, which can be mixed with water and has good dispersion compatibility, and is easy to paint with flowability. It has good physical properties after hardening. It is widely used in concrete cement surface, and has good bonding effect on wet surface and new and old concrete. This product is a healthy green building material.

Application

  • Adhesion between new and old concrete.

Features

  • Good fluidity and easy to use.
  • The cured film has excellent physical properties and water resistance.
  • It is easy to mix and use with water, and there is no pollution problem.
  • Eco-friendly.

Directions

  1. 200g/m2 for one painting/coating.
  2. Mix agent A and agent B evenly according to the ratio and apply with trowels, roller brushes or (airless) machine spray.

Notice

  1. The materials should be fully mixed evenly according to the correct ratio, and avoid the heat accumulation reaction caused by the mixed materials being placed in the barrel for too long.
  2. The materials must be used up within the reaction time during painting. They must NOT be used if there is gelation, and new materials should be used.
  3. The product should be stored in a cool, dry place and avoid direct sunlight.
  4. For painting in humid climate or weather with relative humidity above 85%, the next procedure needs to be carried out after it is dry.
  5. After painting, don’t get in touch with rain directly, otherwise, it may affect physical properties of coating.
  6. There should be no oil stains, sand, moisture or dust on the surface of the coated object. The surface must be cleaned up.